The changes are just too extensive for lazy me to list them
there, but see the comment at the top of sysdep/unix/krt.c.
The code got a bit more ifdeffy than I'd like, though.
Also fixed a bunch of FIXME's and added a couple of others. :)
addresses per interface (needed for example for IPv6 support).
Visible changes:
o struct iface now contains a list of all interface addresses (represented
by struct ifa), iface->addr points to the primary address (if any).
o Interface has IF_UP set iff it's up and it has a primary address.
o IF_UP is now independent on IF_IGNORED (i.e., you need to test IF_IGNORED
in the protocols; I've added this, but please check).
o The if_notify_change hook has been simplified (only one interface pointer
etc.).
o Introduced a ifa_notify_change hook. (For now, only the Direct protocol
does use it -- it's wise to just listen to device routes in all other
protocols.)
o Removed IF_CHANGE_FLAGS notifier flag (it was meaningless anyway).
o Updated all the code except netlink (I'll look at it tomorrow) to match
the new semantics (please look at your code to ensure I did it right).
Things to fix:
o Netlink.
o Make krt-iface interpret "eth0:1"-type aliases as secondary addresses.
operations on 2.1/2.2 kernels. This allows passing of real interface
indexes instead of referencing interfaces by their IP addresses which
fails badly in presence of unnumbered interfaces.
Unfortunately, this structure is not visible with glibc 2.0 as it provides
its own networking headers :-( Both libc5 and glibc 2.1 should be OK.
o Now compatible with filtering.
o Learning of kernel routes supported only on CONFIG_SELF_CONSCIOUS
systems (on the others it's impossible to get it semantically correct).
o Learning now stores all of its routes in a separate fib and selects
the ones the kernel really uses for forwarding packets.
o Better treatment of CONFIG_AUTO_ROUTES ports.
o Lots of internal changes.
o Nothing is configured automatically. You _need_ to specify
the kernel syncer in config file in order to get it started.
o Syncing has been split to route syncer (protocol "Kernel") and
interface syncer (protocol "Device"), device routes are generated
by protocol "Direct" (now can exist in multiple instances, so that
it will be possible to feed different device routes to different
routing tables once multiple tables get supported).
See doc/bird.conf.example for a living example of these shiny features.
(via Netlink). Tweaked kernel synchronization rules a bit. Discovered
locking bug in kernel Netlink :-)
Future plans: Hunt all the bugs and solve all the FIXME's.
over EFence and also hopefully smaller memory overhead, but sadly it's non-free
for commercial use).
If the DMALLOC_OPTIONS environment variable is not set, switch on `reasonable'
checks by default.
Also introduced mb_allocz() for cleared mb_alloc().
The new kernel syncer is cleanly split between generic UNIX module
and OS dependent submodules:
- krt.c (the generic part)
- krt-iface (low-level functions for interface handling)
- krt-scan (low-level functions for routing table scanning)
- krt-set (low-level functions for setting of kernel routes)
krt-set and krt-iface are common for all BSD-like Unices, krt-scan is heavily
system dependent (most Unices require /dev/kmem parsing, Linux uses /proc),
Netlink substitues all three modules.
We expect each UNIX port supports kernel routing table scanning, kernel
interface table scanning, kernel route manipulation and possibly also
asynchronous event notifications (new route, interface state change;
not implemented yet) and build the KRT protocol on the top of these
primitive operations.
o Introduced if_find_by_index()
o Recognizing two types of interface updates: full update (starting with
if_start_update(), ending with if_end_update(), guaranteed to see
all existing interfaces) and a partial update (only if_update(),
usually due to asynchronous interface notifications).
o Introduced IF_LINK_UP flag corresponding to real link state.
o Allowed addressless interfaces.
o IF_UP is now automatically calculated and set iff the interface
is administratively up, has link up and has an IP address assigned.
It may be IF_IGNORED, though (as in case of the loopback).
o Any changes which include up/down transition are considered small
enough to not provoke artificial upping and downing of the interface.
o When an interface disappears (i.e., it wasn't seen in the last scan),
we announce this change only once.
o IF_LOOPBACK implies IF_IGNORE.
of various callbacks.
Events are just another resource type objects (thus automatically freed
and unlinked when the protocol using them shuts down). Each event can
be linked in at most one event list. For most purposes, just use the
global event list handled by the following functions:
ev_schedule Schedule event to be called at the next event
scheduling point. If the event was already
scheduled, it's just re-linked to the end of the list.
ev_postpone Postpone an already scheduled event, so that it
won't get called. Postponed events can be scheduled
again by ev_schedule().
You can also create custom event lists to build your own synchronization
primitives. Just use:
ev_init_list to initialize an event list
ev_enqueue to schedule event on specified event list
ev_postpone works as well for custom lists
ev_run_list to run all events on your custom list
ev_run to run a specific event and dequeue it
#define L_DEBUG "\001" /* Debugging messages */
#define L_INFO "\002" /* Informational messages */
#define L_WARN "\003" /* Warnings */
#define L_ERR "\004" /* Errors */
#define L_AUTH "\005" /* Authorization failed etc. */
#define L_FATAL "\006" /* Fatal errors */
#define L_TRACE "\002" /* Protocol tracing */
#define L_INFO "\003" /* Informational messages */
#define L_REMOTE "\004" /* Remote protocol errors */
#define L_WARN "\004" /* Local warnings */
#define L_ERR "\005" /* Local errors */
#define L_AUTH "\006" /* Authorization failed etc. */
#define L_FATAL "\007" /* Fatal errors */
#define L_BUG "\010" /* BIRD bugs */
Introduced bug() which is like die(), but with level L_BUG. Protocols
should _never_ call die() as it should be used only during initialization
and on irrecoverable catastrophic events like out of memory.
Also introduced ASSERT() which behaves like normal assert(), but it calls
bug() when assertion fails. When !defined(DEBUGGING), it gets ignored.
