Use full time precision to initialize random generator. The old
code was prone to initialize it to the same values in specific
circumstances (boot without RTC, multiple VMs starting at once).
This patch adds support for source-specific IPv6 routes to BIRD core.
This is based on Dean Luga's original patch, with the review comments
addressed. SADR support is added to network address parsing in confbase.Y
and to the kernel protocol on Linux.
Currently there is no way to mix source-specific and non-source-specific
routes (i.e., SADR tables cannot be connected to non-SADR tables).
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
On Linux, setting the ToS will also set the priority and the range of
accepted values is quite limited (masked by 0x1e). Therefore, 0xc0 is
translated to a priority of 0, not something we want, overriding the
"7" priority which was set previously explicitely. To avoid that, just
move setting priority later in the code.
Thanks to Vincent Bernat for the patch.
A filter should log messages only if executed explicitly (e.g., during
route export or route import). When a filter is executed for technical
reasons (e.g., to establish whether a route was exported before), it
should run silently.
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Anyway, Bird is now capable to insert both MPLS routes and MPLS encap
routes into kernel.
It was (among others) needed to define platform-specific AF_MPLS to 28
as this constant has been assigned in the linux kernel.
No support for BSD now, it may be added in the future.
Dropped struct mpnh and mpnh_*()
Now struct nexthop exists, nexthop_*(), and also included struct nexthop
into struct rta.
Also converted RTD_DEVICE and RTD_ROUTER to RTD_UNICAST. If it is needed
to distinguish between these two cases, RTD_DEVICE is equivalent to
IPA_ZERO(a->nh.gw), RTD_ROUTER is then IPA_NONZERO(a->nh.gw).
From now on, we also explicitely want C99 compatible compiler. We assume
that this 20-year norm should be known almost everywhere.
