If the next hop of a route is not a reachable address, the route should be
installed as onlink. This enables a configuration common in mesh networks
where the mesh interface is assigned a /32 and babel handles the routing by
installing onlink routes.
Thanks to Toke Hoiland-Jorgensen for the patch.
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
There are three common ways how to encode IPv6 link-local-only next hops:
(:: ll), (ll), and (ll ll). We use the first one but we should accept all
three. The patch fixes handling of the last one.
Thanks to Sebastian Hahn for the bugreport.
The RFC 5575 does not explicitly reject flowspec rules without dst part,
it just requires dst part in validation procedure for feasibility, which
we do not implement anyway. Thus flow without dst prefix is syntactically
valid, but unfeasible (if feasibilty testing is done).
Thanks to Alex D. for the bugreport.
When dynamic BGP with remote range is configured, MD5SIG needs to use
newer socket option (TCP_MD5SIG_EXT) to specify remote addres range for
listening socket.
Thanks to Adam Kułagowski for the suggestion.
Recent changes in neighbor code caused RIP to access neighbor field which
is NULL during interface/neighbor removal and caused crash when debug
messages are enabled. Use correct field to get iface from neighbor.
During NLRI parsing of IPv6 Flowspec, dst prefix was not properly
extracted from NLRI, therefore a received flow was stored in a different
position in flowspec routing table, and was not reachable by command
'show route <flow>'.
Add proper prefix part accessors to flowspec code and use them from BGP
NLRI parsing code.
Thanks to Alex D. for the bugreport.
This is optional check described in RFC 4271. Although this can be also
done by filters, it is widely implemented option in BGP implementations.
Thanks to Eugene Bogomazov for the original patch.
Transitive extended communities should be removed on external sessions,
the old code them in all cases.
Thanks to Jean-Daniel Pauget for the original patch.
Change of some options requires route refresh, but when import table is
active, channel reload is done from it instead of doing full route
refresh. So in this case we request it internally.
The bfd_reconfigure_neighbors() returned after first reconfigured
neighbor instead of continuing with the next one.
Thanks to Winston Chen for the bugreport and a patch.
There is an improper check for valid message size, which may lead to
stack overflow and buffer leaks to log when a large message is received.
Thanks to Daniel McCarney for bugreport and analysis.
Instead of having large stack buffer for max amount of AFI/SAFI pairs.
The old code is not correct w.r.t. extendeded option length, as more
AFI/SAFI pairs may fit into the capability option.
The patch implements optional internal export table to a channel and
hooks it to BGP so it can be used as Adj-RIB-Out. When enabled, all
exported (post-filtered) routes are stored there. An export table can be
examined using e.g. 'show route export table bgp1.ipv4'.
Several BGP channel options (including 'next hop self') could be
reconfigured without session reset, with just route refeed/refresh.
The patch improves reconfiguration code to do it that way.
The 'deterministic med' option is implemented by suppressing other than
best-in-group routes (grouped by ASN) from best route selection. This
interferes with 'merge paths' as supressed routes are no longer mergable
with best route. This is fixed by suppressing only those routes that are
not mergable with best-in-group route.
Protocol can have specified VRF, in such case it is restricted to a set
of ifaces associated with the VRF, otherwise it can use all interfaces.
The patch allows to specify VRF as 'default', in which case it is
restricted to a set of iface not associated with any VRF.
Per RFC 3101, N-bit signalling NSSA support should be used only in Hello
packets, not in DBDES packets. BIRD since 2.0.4 verifies N-bit in
neighbor structure, which is learned from DBDES packets, therefore
NSSA-LSAs are not propagated to proper implementations of RFC 3101.
This patch fixes that. Both removing the check and removing N-bit from
DBDES packet. This will fix compatibility issues with proper
implementations, but causes compatibility issues with BIRD 2.0.4.
We need to flush learned external LSAs a bit later than other LSAs (after
first feed after end of the graceful restart) to avoid flap of external
routes.
If BGP has too many data to send and BIRD is slower than the link, TX is
always possible until all data is sent. This patch limits maximum number
of generated BGP messages in one iteration of TX hook.
Implement OSPFv2 (RFC 3623) and OSPFv3 (RFC 5187) graceful restart,
for both restarting and helper sides. Graceful restart is initiated
by 'graceful down' command.
When 'graceful down' command is entered, protocols are shut down
with regard to graceful restart. Namely Kernel protocol does
not remove routes and BGP protocol does not send notification,
just closes the connection.
Useful for implementation of agents implementing the SNMP-BGP MIB, which
requires the local AS of a session to be specified.
Thanks to Jan-Philipp Litza for the patch.
Support for dynamically spawning BGP protocols for incoming connections.
Use 'neighbor range' to specify range of valid neighbor addresses, then
incoming connections from these addresses spawn new BGP instances.
When BGP connection is opened, it may happen that rx hook (with remote
OPEN) is called before tx hook (for local OPEN). Therefore, we need to do
internal changes (like setting local_caps) synchronously with OPENSENT
transition and we need to ensure that OPEN is sent before KEEPALIVE.
Allow to specify just 'internal' or 'external' for remote neighbor
instead of specific ASN. In the second case that means BGP peers with
any non-local ASNs are accepted.
The temporary atttributes are no longer removed by ea_do_prune(), but
they are undefined by store_tmp_attrs() protocol hooks. This fixes
several bugs where temporary attributes were removed when they should
not or not removed when they should be. The flag EAF_TEMP is no longer
needed and was removed.
Update all protocol make_tmp_attrs() / store_tmp_attrs() hooks to use
helper functions and to handle unset attributes properly.
Also fix some related bugs like improper handling of empty eattr list.
Keep track of whether OSPF tmpattrs are actually defined for given route
(using flags in rte->pflags). That makes them behave more like real
eattrs so a protocol can define just a subset of them or they can be
undefined by filters.
Do not set ospf_metric2 for other than type 2 external OSPF routes and do
not set ospf_tag for non-external OSPF routes. That also fixes a bug
where internal/inter-area route propagated from one OSPF instance to
another is initiated with infinity ospf_metric2.
Thanks to Yaroslav Dronskii for the bugreport.
This is a major change of how the filters are interpreted. If everything
works how it should, it should not affect you unless you are hacking the
filters themselves.
Anyway, this change should make a huge improvement in the filter performance
as previous benchmarks showed that our major problem lies in the
recursion itself.
There are also some changes in nest and protocols, related mostly to
spreading const declarations throughout the whole BIRD and also to
refactored dynamic attribute definitions. The need of these came up
during the whole work and it is too difficult to split out these
not-so-related changes.
When area is reconfigured to a different type, we need to flush LSAs as
they may not be valid (e.g. NSSA-LSA for non-NSSA area). Also, when we
have have just one OSPF area and that changes type, we could restart OSPF
as there is no state to keep anyway. That solves issue with different
handling of external routes exported to OSPF based of main area type.
External LSAs originated by OSPF routers with VPN-PE behavior enabled are
marked by DN flag and they are ignored by other OSPF routers with VPN-PE
enabled.
Direct acknowledgements should be send as unicast to a corresponding
neighbor. Only delayed acks should be send as multicast to all/designated
routers.
Master may free last DBDES packet immediately. Slave must wait dead
interval before freeing last DBDES packet and then reject duplicate
DBDES packets with SeqNumberMismatch.
