As specified in RFC 2328 8.1: "On physical point-to-point networks,
the IP destination is always set to the address AllSPFRouters."
Note that this likely break setups with multiple neighbors on a network
configured as PtP, which worked before. These should be configured as
PtMP.
Thanks to Senthil Kumar Nagappan for the original patch and to Joakim
Tjernlund for suggestions.
The flag makes sense just in external representation. It is reset during
BGP export, but keeping it internally broke MRT dumps for short attributes
that used it anyways.
Thanks to Simon Marsh for the bugreport and the patch.
BGP statistics code was preliminary and i wanted to replace it by
separate 'show X stats' command. The patch hides the preliminary
output in 'show protocols all' so it is not part of the released
version.
In OSPFv3, only Hello and DBDes packets contain flags specifying whether
RFC 7166 authentication trailer is used. Other packets are processed
based on stored authentication state in neighbor structure. Update this
state with each received Hello to handle authentication change from
reconfigurations.
Thanks to Joakim Tjernlund and Kenth Eriksson for the bugreport.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
Flag signalling that MP-BGP mode should be used got reset after first
batch of routes, so remaining routes were processed without that, leading
to missing MP_REACH_NLRI attribute.
Thanks to Piotr Wydrych for the bugreport.
Add fake MP_REACH_NLRI attribute with BGP next hop when encoding MRT
table dumps for IPv6 routes. That is necessary to encode next hop as
NEXT_HOP attribute is not used for MP-BGP.
Thanks to Santiago Aggio for the bugreport.
Direct BFD sessions needs to be dispatched not only by IP addresses, but
also by interfaces, in order to avoid collisions between neighbors with
the same IPv6 link-local addresses.
Extend BFD session hash_ip key by interface index to handle that. Use 0
for multihop sessions.
Thanks to Sebastian Hahn for the original patch.
It was mixed-up if hostname is IPv6 address, and reporting separate
values (like port) on separate lines fits better into key-value style
of 'show protocols all' output. Also, the patch simplifies transport
identification formatting (although it is unused now).
Thanks to Alarig Le Lay for the suggestion.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
The patch add support for per-channel debug flags, currently just
'states', 'routes', and 'filters'. Flag 'states' is used for channel
state changes, remaining two for routes passed through the channel.
The per-protocol debug flags 'routes'/'filters' still enable reporting
of routes for all channels, to keep existing behavior.
The patch causes minor changes in some log messages.
When config structures are copied due to template application,
we need to reset list node structure before calling add_tail().
Thanks to Mikael Magnusson for patches.
The babel protocol code was initialising objects returned from the slab
allocator by assigning to each of the struct members individually, but
wasn't touching the NODE member while doing so. This leads to warnings on
debug builds since commit:
baac700906 ("List expensive check.")
To fix this, introduce an sl_allocz() variant of the slab allocator which
will zero out the memory before returning it, and switch all the babel call
sites to use this version. The overhead for doing this should be negligible
for small objects, and in the case of babel, the largest object being
allocated was being zeroed anyway, so we can drop the memset in
babel_read_tlv().
Add support for proper handling of multiple routes with the same network
to the static protocol. Routes are distinguished by internal index, which
is assigned automatically (sequentially for routes within each network).
Having different route preference or igp_metric attribute is optional.
When a new link-LSA is originated, we need to notify intra-area-prefix-LSA
handling, like when a new link-LSA is received. Otherwise a new network
prefix added to a DR is not propagated immediately.
Thanks to Bala Sajja for the bugreport.
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
Add 'ignore max length' option to RPKI protocol, which ignores received
max length in ROA records and instead uses max value (32 or 128). This
may be useful for implementing loose RPKI check for blackholes.
Sometimes multicast OSPF packet is received when neighbor adjacency is
not established. Such packet should be ignored earlier in packet
processing as otherwise it causes strange error messages when OSPFv3
authentication is enabled.
Most commands like 'show ospf neighbors' fail when protocol is not
specified and there are multiple instances of given protocol type.
This is annoying in BIRD 2, as many protocols have IPv4 and IPv6
instances. The patch changes that by showing output from all protocol
instances of appropriate type.
Note that the patch also removes terminating cli_msg() call from these
commands and moves it to the common iterating code.
Compare the new timing parameters with the old configuration, not with
the temporary state of the current connection.
The timing values in struct rpki_cache is updated by a version 1 End Of
Data PDU, unless this behavior is suppressed by the configuration
explicitly by the "keep" keyword. Consequently, every reconfiguration
of BIRD triggers a reconnection even if it is not necessary.
If the next hop of a route is not a reachable address, the route should be
installed as onlink. This enables a configuration common in mesh networks
where the mesh interface is assigned a /32 and babel handles the routing by
installing onlink routes.
Thanks to Toke Hoiland-Jorgensen for the patch.
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
There are three common ways how to encode IPv6 link-local-only next hops:
(:: ll), (ll), and (ll ll). We use the first one but we should accept all
three. The patch fixes handling of the last one.
Thanks to Sebastian Hahn for the bugreport.
