After switching to 16-way tries, trie format ignored unaligned / internal
prefixes and only reported the primary prefix of a trie node.
Fix trie format by showing internal prefixes based on the 'local' bitmask
of a node. Also do basic (intra-node) reconstruction of prefix patterns
by finding common subtrees in 'local' bitmask.
In future, we could improve that by doing inter-node reconstruction, so
prefixes entered as one pattern for a subtree (e.g. 192.168.0.0/18+)
would be reported as such, like with aligned prefixes.
The prune loop may may rebuild the prefix trie and therefore invalidate
walk state for asynchronous walks (used in 'show route in' cmd). Fix it
by adding locking that keeps the old trie in memory until current walks
are done.
In future this could be improved by rebuilding trie walk states (by
lookup for last found prefix) after the prefix trie rebuild.
When rtable is pruned and network fib nodes are removed, we also need to
prune prefix trie. Unfortunately, rebuilding prefix trie takes long time
(got about 400 ms for 1M networks), so must not be atomic, we have to
rebuild a new trie while current one is still active. That may require
some considerable amount of temporary memory, so we do that only if
we expect significant trie size reduction.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
When output of 'show route' command was generated, the net_format() was
called for each network prematurely, even if the result was not needed.
Fix the code to call net_format() only when needed. This makes queries
that process many networks but show only few (e.g. 'show route where ..',
or 'show route count') much faster (like 5x - 10x faster).
Attach a prefix trie to IP/VPN/ROA tables. Use it for net_route() and
net_roa_check(). This leads to 3-5x speedups for IPv4 and 5-10x
speedup for IPv6 of these calls.
TODO:
- Rebuild the trie during rt_prune_table()
- Better way to avoid trie_add_prefix() in net_get() for existing tables
- Make it configurable (?)
For convenience, Trie functions generally accept as input values not only
NET_IPx types of nets, but also NET_VPNx and NET_ROAx types. But returned
values are always NET_IPx types.
The prefix trie now supports longest-prefix-match query by function
trie_match_longest_ipX() and it can be extended to iteration over all
covering prefixes for a given prefix (from longest to shortest) using
TRIE_WALK_TO_ROOT_IPx() macro.
Trie walking allows enumeration of prefixes in a trie in the usual
lexicographic order. Optionally, trie enumeration can be restricted
to a chosen subnet (and its descendants).
Add trie tests intended as benchmarks that use external datasets
instead of generated prefixes. As datasets are not included, they
are commented out by default.
Use 16-way (4bit) branching in prefix trie instead of basic binary
branching. The change makes IPv4 prefix sets almost 3x faster, but
with more memory consumption and much more complicated algorithm.
Together with a previous filter change, it makes IPv4 prefix sets
about ~4.3x faster and slightly smaller (on my test data).
Pipes copy the original rte with old values, so they require rte to be
exported with stored tmpattrs. Other protocols access stored attributes
using eattr list, so they require rte to be exported with expanded
tmpattrs. This is temporary hack, we plan to remove whoe tmpattr mechanism.
Thanks to Paul Donohue for the bugreport.
In most cases of export there is no need to store back temporary
attributes to rte, as receivers (protocols) access eattr list anyway.
But pipe copies the original rte with old values, so we should store
tmpattrs also during export.
Thanks to Paul Donohue for the bugreport.
Some cleanups and bugfixes to the previous patch, including:
- Fix rate limiting in index mismatch check
- Fix missing BABEL_AUTH_INDEX_LEN in auth_tx_overhead computation
- Fix missing auth_tx_overhead recalculation during reconfiguration
- Fix pseudoheader construction in babel_auth_sign() (sport vs fport)
- Fix typecasts for ptrdiffs in log messages
- Make auth log messages similar to corresponding RIP/OSPF ones
- Change auth log messages for events that happen during regular
operation to debug messages
- Switch meaning of babel_auth_check*() functions for consistency
with corresponding RIP/OSPF ones
- Remove requirement for min/max key length, only those required by
given MAC code are enforced
This implements support for MAC authentication in the Babel protocol, as
specified by RFC 8967. The implementation seeks to follow the RFC as close
as possible, with the only deliberate deviation being the addition of
support for all the HMAC algorithms already supported by Bird, as well as
the Blake2b variant of the Blake algorithm.
For description of applicability, assumptions and security properties,
see RFC 8967 sections 1.1 and 1.2.
In preparation for adding authentication checks, refactor the TLV
walking code so it can be reused for a separate pass of the packet
for authentication checks.
Add support for specifying a password in hexadecimal format, The result
is the same whether a password is specified as a quoted string or a
hex-encoded byte string, this just makes it more convenient to input
high-entropy byte strings as MAC keys.
Import the blake2-kat.h header with test vector output from the blake
reference implementation, and add tests to mac_test.c to compare the
output of the Bird MAC algorithm implementations with that reference
output.
Since the reference implementation only has test vectors for the full
output size, there are no tests for the smaller-sized output variants.
The Babel MAC authentication RFC recommends implementing Blake2s as one of
the supported algorithms. In order to achieve do this, add the blake2b and
blake2s hash functions for MAC authentication. The hashing function
implementations are the reference implementations from blake2.net.
The Blake2 algorithms allow specifying an arbitrary output size, and the
Babel MAC spec says to implement Blake2s with 128-bit output. To satisfy
this, we add two different variants of each of the algorithms, one using
the default size (256 bits for Blake2s, 512 bits for Blake2b), and one
using half the default output size.
Update to BIRD coding style done by committer.
Add a wrapper function in sysdep to get random bytes, and required checks
in configure.ac to select how to do it. The configure script tries, in
order, getrandom(), getentropy() and reading from /dev/urandom.
Routes from downed protocols stay in rtable (until next rtable prune
cycle ends) and may be even exported to another protocol. In BGP case,
source BGP protocol is examined, although dynamic parts (including
neighbor entries) are already freed. That may lead to crash under some
race conditions. Ensure that freed neighbor entry is not accessed to
avoid this issue.
When an interface disappears, all the neighbors are freed as well. Seqno
requests were anyway not decoupled from them, leading to strange
segfaults. This fix adds a proper seqno request list inside neighbors to
make sure that no pointer to neighbor is kept after free.
.gitlab-ci.yml:
+ pkg targets for some distros added
+ artifacts added
- some distros were commented out (due to errors).
misc/docker/*:
+ Dockerfiles updated with the necessary packages.
